When purchasing a fishing net, buyers usually focus on material, mesh size, twine thickness, length, and width.
But there is another factor that can strongly influence how a net behaves after installation: hanging ratio.
A fishing net may have the correct material and mesh specification, yet still look too tight, too loose, too narrow, or unusually deep after mounting. In many cases, the problem is not the net itself. It is the relationship between the netting and the rope or frame supporting it.
Understanding hanging ratio can help fishermen, aquaculture operators, wholesalers, and marine project buyers achieve better net shape, installation, and working performance.
A piece of fishing netting contains many mesh openings that can change shape when stretched.
When netting is attached to a rope, frame, or support line, the net is normally not fixed at its maximum stretched length.
Instead, a certain amount of netting is distributed along a shorter supporting length.
This relationship affects the final shape of the mesh.
Depending on how the net is mounted, the openings may appear:
Wider
Narrower
Deeper
More diamond-shaped
More vertically stretched
This is why the same netting material can produce very different finished nets.
Unlike plastic panels or metal fencing, fishing netting does not have one completely fixed shape.
Its geometry changes when tension changes.
Pull the net horizontally and the mesh becomes wider.
Increase vertical tension and the mesh becomes longer and narrower.
This flexibility is useful because it allows fishing nets to adapt to different working conditions.
However, it also means that finished dimensions cannot always be understood simply by laying an unstretched net on the floor.
The installation method matters.
If netting is stretched too strongly along its horizontal direction, the mesh openings may become wide and shallow.
The entire panel can lose depth.
This may affect how the finished net performs during fishing or aquaculture use.
Excessive stretching can also increase tension around:
Knots
Border ropes
Seams
Corners
Attachment points
A net does not necessarily perform better simply because it looks very tight.
Proper installation should allow the mesh to maintain the intended working shape.
If too much netting is placed along a short support rope, the panel may become heavily gathered.
This can create extra folds and uneven areas.
A very loose net may:
Move more in current
Rub against nearby equipment
Become difficult to inspect
Produce irregular mesh shapes
Create unwanted sagging
Therefore, both excessive tension and excessive looseness can reduce practical performance.
The goal is to create a balanced structure.
In capture fishing, mesh shape can affect how a fishing net interacts with fish.
The same nominal mesh size may behave differently when mounted using different hanging arrangements.
A more open mesh geometry may create one type of fishing behavior, while a narrower mesh shape may create another.
For this reason, experienced fishing operations often consider not only the mesh measurement but also how the finished net will be mounted.
When replacing an existing commercial net, buyers should provide as much information as possible about the original construction.
Hanging ratio is equally relevant for aquaculture.
Fish cage netting must maintain sufficient internal volume while remaining properly connected to the cage structure.
If the net is mounted incorrectly, parts of the cage may become:
Too tight
Too shallow
Uneven
Distorted
More vulnerable to concentrated stress
A correctly assembled cage net should work with the frame, ropes, weights, and surrounding water conditions as one complete system.
This is particularly important for larger cages where small dimensional differences can become significant across the entire structure.
A buyer might order a net with the same mesh size as a previous product and still notice that the finished net behaves differently.
Several reasons are possible.
The differences may come from:
Measurement method
Twine material
Twine diameter
Netting construction
Heat setting
Hanging arrangement
Finished assembly
This is why copying only one specification from an old fishing net may not reproduce the same finished result.
For replacement nets, samples, drawings, photos, and complete specifications can be extremely useful.
Fishing net panels are often assembled with ropes along the top, bottom, or sides.
These ropes help determine how the net is positioned.
If the rope length does not match the intended netting arrangement, the mesh may become distorted.
Correct border construction helps maintain:
Panel dimensions
Mesh orientation
Attachment stability
More even tension
For customized finished nets, border rope length should therefore be considered together with the net panel dimensions.
Even if the correct hanging arrangement is planned, poor attachment spacing can still create problems.
If some sections are packed closely while others are stretched farther apart, the mesh will not distribute evenly.
The result may look wavy or irregular.
Consistent attachment spacing helps the net maintain a more uniform geometry.
This is particularly important along:
Top ropes
Bottom ropes
Side borders
Seams
Cage frames
Installation quality and manufacturing quality must work together.
A fishing net may look perfect while lying on land.
Once placed in water, current begins pushing against the mesh.
The net may move, stretch, or change depth depending on:
Water speed
Mesh size
Twine thickness
Net dimensions
Weights
Floats
Supporting ropes
Therefore, the correct hanging arrangement should consider actual working conditions rather than appearance alone.
Large underwater nets need enough flexibility to respond to water movement without creating excessive stress.
Marine growth gradually covers the twine of nets used underwater.
As algae and other organisms accumulate, the net becomes heavier and water resistance increases.
This can alter the way the panel hangs.
Sections that originally had balanced tension may begin to sag or pull differently.
Regular maintenance helps operators identify these changes before they become serious.
When inspecting an aquaculture net, pay attention not only to broken mesh but also to changes in overall shape.
Custom fishing net orders often involve misunderstandings about dimensions.
For example, a buyer may request a certain width without explaining whether that dimension refers to:
Fully stretched netting
Installed finished width
Rope length
Working depth
Panel size before assembly
These measurements are not always interchangeable.
Clear communication before production is essential.
Manufacturers and buyers should agree on how dimensions are defined and measured.
This is particularly important for large customized nets.
If a buyer wants to reproduce an existing net but does not know its technical construction, sending a physical sample can be extremely helpful.
A manufacturer can examine factors such as:
Mesh size
Twine structure
Material
Knot style
Border construction
General mesh geometry
Photos and videos can also help explain how the net is installed.
The more complete the information, the easier it is to develop a suitable replacement.
For simple rolls of netting, basic dimensions may be enough.
For complicated finished nets, technical drawings can greatly improve communication.
A drawing can show:
Overall dimensions
Panel positions
Border ropes
Connection points
Openings
Reinforced areas
Attachment loops
Special structures
This is particularly useful for aquaculture cages, customized fishing gear, large net panels, and marine protection systems.
Fishing net performance comes from the combination of many factors.
Material matters.
Twine thickness matters.
Mesh size matters.
But the way that mesh is arranged and installed also matters.
A strong net mounted incorrectly may perform poorly.
A correctly selected and properly assembled net can maintain a more suitable shape, distribute stress more evenly, and work more naturally in its intended environment.
When requesting a customized fishing net quotation, buyers should ideally provide:
Application
Material
Mesh size
Twine specification
Required dimensions
Border rope requirements
Installation method
Quantity
Working environment
For existing products, photos, drawings, or samples can provide additional useful information.
Professional fishing net production is not simply about making a piece of mesh.
It is about matching the net structure to the way it will actually be installed and used.
Understanding hanging ratio is one more step toward choosing fishing nets that perform more predictably in fishing, aquaculture, and marine applications.
If you need fishing nets, aquaculture cage nets, custom net panels, ropes, or finished net assemblies, contact us with your required specifications, drawings, samples, or application details. We can provide customized production according to your actual fishing or aquaculture requirements.
For purchase or customization inquiries, click the link below to learn more details