Cleaning is essential for fishing nets used in aquaculture and marine environments.
It helps remove:
Algae
Slime
Mussels
Barnacles
Sediment
Organic buildup
But cleaning equipment can also damage the net if the contact pressure, tool surface, operating speed, or cleaning method is too aggressive.
The damage may not cause immediate failure.
Instead, repeated cleaning can gradually create weak zones that later break under normal operating loads.
The key principle is:
Cleaning damage usually leaves a recognizable pattern because the tool repeatedly contacts the net in a controlled direction or path.
Cleaning equipment usually moves in a predictable direction.
This can create:
Horizontal wear bands
Vertical wear bands
Repeated parallel lines
Local strips of polished twine
If the damage follows the movement of the cleaning tool, cleaning-related abrasion becomes a strong possibility.
One of the simplest inspection methods is comparison.
Check whether the most frequently cleaned areas show more:
Fuzzing
Flattening
Diameter loss
Broken outer filaments
than protected or less-accessible sections.
A strong difference can indicate cleaning-related wear.
Mechanical brushes can gradually damage outer filaments.
The twine may become:
Hairy
Rough
Frayed
Less compact
Small amounts of fuzzing do not automatically mean severe strength loss, but progressive fuzzing should be monitored.
Not all cleaning damage looks rough.
Smooth brushes, rollers, or repeated sliding contact can polish the surface.
Look for:
Unusually shiny areas
Smooth flattened tracks
Surface gloss different from nearby mesh
This can be an early stage of abrasion.
Repeated pressure from cleaning equipment can change the cross-section of the twine.
Originally round twine may become:
Oval
Flat
Compressed
This is especially important if the equipment pushes the net against a hard support such as a frame or pipe.
A flattened twine can still appear thick when measured from the wide side.
Rotate the measurement direction.
Compare:
Maximum width
Minimum thickness
A large difference may reveal compression or wear that one reading would miss.
Hard brushes, scraper edges, rotating parts, or damaged cleaning equipment may create sharper defects.
Check for:
Short cuts
Grooves
Notches
Partial strand separation
These defects are more serious than simple surface polishing because they can reduce the remaining cross-section quickly.
Cleaning often pushes the net toward:
Cage frames
Sinker tubes
Metal rings
Border ropes
The cleaning tool may not be the only damaging surface.
Damage can occur because the net is trapped between the cleaner and the structure behind it.
One side may show brush contact.
The opposite side may show:
Flattening
Hard pressure marks
Frame abrasion
Inspecting only the cleaned face can miss half of the damage mechanism.
Borders are stiffer than the main panel.
When a cleaning tool reaches the edge, the net cannot move as freely.
This can increase local pressure.
Inspect:
First mesh rows
Border lacing
Edge knots
Attachment loops
for concentrated wear.
Cleaning equipment may change direction near corners.
Operators may also spend more time cleaning heavily fouled corner areas.
This can create repeated:
Scrubbing
Pressure
Contact with reinforcement
Corners should therefore receive extra inspection.
A seam is usually thicker and less flexible than the main mesh.
When cleaning equipment passes over the seam, contact pressure may increase.
Damage may appear:
On the seam
Beside the seam
One mesh row away
The failure does not always occur directly on the thickest part.
A rotating brush can repeatedly pull outer filaments in the same direction.
The twine may develop:
One-sided fuzzing
Strand lifting
Directional fraying
This pattern can help distinguish brush damage from random marine abrasion.
Aggressive bristles can remove fouling effectively but also increase stress on the twine surface.
The risk becomes greater when:
Brush pressure is high
Speed is high
Netting is already aged
Twine is heavily fouled
The cleaning method should match the condition of the net.
A damaged brush may develop:
Sharp bristle ends
Exposed metal
Uneven contact zones
The cleaner itself should therefore be inspected regularly.
A machine that was safe when new may become damaging after wear.
Scrapers are especially risky if they contact twine directly.
Possible signs include:
Straight cuts
Repeated notches
Abrupt strand damage
These patterns can differ significantly from gradual biological or current-related wear.
Water jets do not normally create the same rubbing marks as brushes.
However, excessive pressure at close distance can:
Move knots
Open damaged strands
Distort mesh
Worsen existing cuts
The effect depends on pressure, nozzle distance, angle, and twine condition.
Cleaning equipment may not create the original defect.
Instead, it may enlarge:
Old abrasion
Small cuts
Loose filaments
Weak knots
This is why cleaning-related failure can involve both previous aging and new mechanical damage.
Thick fouling often requires more aggressive cleaning.
Operators may use:
Greater brush pressure
More passes
Slower movement
The net underneath may already be aged or abraded.
This combination increases the chance of damage.
Fouling is undesirable, but it can partially cover and protect some surfaces from direct contact.
After cleaning, the exposed twine may show:
Hidden wear
Cuts
Flattening
Do not assume the cleaner created every visible defect immediately.
Some may only become visible after fouling is removed.
If operators clean from boats or fixed platforms, certain horizontal zones may receive more frequent contact.
A repeated wear band at the same height can strongly suggest cleaning activity.
If possible, review:
Cleaning dates
Equipment used
Operator method
Number of passes
Areas cleaned
Then compare them with the damage map.
A strong spatial relationship helps identify the root cause.
If wear increases after switching to:
A new brush
New machine
Higher pressure
New scraper
the equipment change may be significant.
This is why maintenance and operating records are useful.
After cleaning, some mesh may remain:
Stretched
Twisted
Flattened
Misaligned
This suggests that cleaning altered more than the surface condition.
Persistent geometric deformation deserves further investigation.
Aggressive cleaning can move or rotate knots.
Look for:
Looser knots
Different tail lengths
Uneven orientation
Enlarged adjacent mesh
Several changed knots along a cleaning path can indicate mechanical disturbance.
Cleaning equipment may push or drag the panel.
You may see:
Elongated mesh
Diagonal wrinkles
Local stretching
Uneven opening size
These signs suggest that significant force was transferred into the net.
This is one of the most useful diagnostic clues.
Natural aging may be broad and gradual.
Cleaning damage often shows:
Repeated lines
Regular spacing
One-sided wear
Concentration near accessible zones
The pattern can reveal how the tool contacted the panel.
Both can create fuzzing and flattening.
The difference is often location.
Hardware abrasion usually follows the exact position of:
Frames
Rings
Tubes
Cleaning damage may extend across a broader moving path.
Sometimes both mechanisms occur together.
Overload more often produces:
Mesh elongation
Knot movement
Multiple connected breaks
Cleaning damage more often shows:
Surface wear
Repeated scratches
Local diameter loss
Again, both can interact.
A cleaned, weakened twine may later fail under normal tension.
A fuzzy twine may still retain useful strength.
A visually smooth twine may already contain hidden damage.
Visual inspection is a screening method.
If remaining capacity matters, representative testing may be required.
Create a simple panel map and identify:
Heavy cleaning zones
Moderate cleaning zones
Protected zones
Compare the same locations during future inspections.
This makes progressive damage easier to identify.
Take close-up photos showing:
Twine surface
Ruler or reference scale
Location on the panel
Nearby seam or hardware
Repeat photographs after later cleaning cycles.
This creates useful maintenance history.
A strong inspection program compares the net:
Before Cleaning
and
After Cleaning
This helps separate:
Existing damage
Newly exposed damage
New cleaning-related damage
Without the “before” condition, root-cause analysis becomes more difficult.
A cleaning method suitable for a new heavy-duty net may be too aggressive for an old, partially worn panel.
Consider:
Net age
Twine diameter
Fouling level
Previous damage
Cleaning intensity should be adjusted accordingly.
More pressure does not always mean better cleaning.
Excessive pressure can:
Flatten twine
Increase abrasion
Move knots
Damage borders
Cleaning should remove fouling without unnecessarily loading the structure.
Inspect:
Brushes
Rollers
Scrapers
Guards
Metal edges
Remove damaged components that could cut or snag the net.
Some damage accumulates slowly.
One cleaning operation may create little visible change.
After repeated cycles, the same surface can become significantly worn.
Trend monitoring is more useful than one isolated inspection.
Look for:
✔ Parallel wear tracks
✔ Fuzzing
✔ Polished surfaces
✔ Flattened twine
✔ Reduced diameter
✔ Cuts or grooves
✔ Broken outer filaments
✔ Knot movement
✔ Mesh distortion
Inspect:
✔ Frequently cleaned zones
✔ Borders
✔ Corners
✔ Seams
✔ Hardware-contact areas
✔ Both sides of the panel
Review:
✔ Cleaning equipment type
✔ Brush condition
✔ Water pressure
✔ Cleaning direction
✔ Number of passes
✔ Cleaning frequency
Investigate further when:
✔ Damage follows a repeated path
✔ Wear increases after cleaning
✔ One side is much more damaged
✔ Several nearby twines show the same pattern
✔ Cleaning and hardware contact overlap
Fishing net cleaning equipment can create damage gradually through:
Repeated abrasion
Compression
Scraping
Excessive pressure
Knot disturbance
The most useful clues are often not the final broken twine but the pattern surrounding it.
The key principle is:
When wear follows the path, direction, or contact zone of the cleaning equipment, the cleaning process should be treated as a possible contributor to the damage.
Reliable diagnosis combines:
Surface Inspection + Damage Mapping + Before/After Comparison + Equipment Check + Cleaning Records + Targeted Strength Testing When Necessary
At PL Fishery, we manufacture PE fishing nets, fish cage panels, aquaculture netting, reinforced borders, attachment loops, repair mesh, repair twine, marine ropes, chicken nets, and customized net products.
To purchase or customize fishing netting for specific cleaning and maintenance conditions, send PL Fishery your mesh size, twine construction, panel dimensions, fouling conditions, cleaning method, contact areas, border structure, abrasion requirements, and inspection criteria so our factory can prepare a suitable production specification.https://plfishery.com/