A fish cage may appear to be one continuous netting system, but different sections of the cage do not experience the same working conditions.
The bottom net and the side nets face different types of stress.
Side nets are mainly affected by:
Water currents
Waves
Fish contact
Frame movement
Bottom nets, however, may experience additional problems such as:
Weight concentration
Sediment contact
Waste accumulation
Uneven loading
Cleaning difficulty
Because of these differences, the bottom of a fish cage may age in a very different way from the sides.
For aquaculture operators, understanding these wear patterns can help improve inspection, maintenance, and net selection.
Side nets are usually more exposed to horizontal water movement.
Currents push directly against the mesh.
This creates:
Drag
Repeated tension
Net deformation
The upstream side may experience especially strong loading.
Over time, this can lead to:
Twine fatigue
Mesh distortion
Edge stress
Side-net wear is therefore often closely related to water flow.
The bottom net has a different role.
It must help maintain the lower shape of the cage.
Depending on the system, it may also support:
Weights
Bottom ropes
Structural tension
This means the bottom may experience more downward and localized loading.
These forces are different from the mainly horizontal loads on side nets.
Fish cages produce:
Feed waste
Feces
Organic particles
Gravity causes much of this material to move downward.
Some waste passes through the bottom mesh.
Some may temporarily accumulate around the net.
This can increase:
Dirt
Biofouling
Cleaning requirements
The bottom net may therefore become more contaminated than upper sections.
In shallow cages or cages near the seabed, the bottom net may come close to:
Sand
Mud
Rocks
If the cage moves with currents or waves, the net may rub against these surfaces.
This can create severe abrasion.
Sand particles can act like an abrasive material.
Repeated contact may gradually:
Thin twine
Damage knots
Weaken fibers
This wear may be very different from the fatigue seen on side nets.
Weights are often used to help maintain cage shape.
If weights or sinker systems are connected near the bottom, load may become concentrated around:
Attachment points
Corners
Border ropes
These areas can experience higher mechanical stress.
Regular inspection is especially important around connections.
Side nets often flex continuously.
They may:
Bow inward
Recover
Move again
This creates repeated fatigue cycles.
Bottom nets may move differently because they are influenced by:
Weighting
Cage depth
Vertical tension
The two areas therefore experience different deformation patterns.
Fish do not use every part of the cage equally.
Some species spend more time:
Near the bottom
Others prefer:
Mid-water
Surface zones
Bottom-dwelling behavior can increase contact with the bottom net.
This may cause more:
Rubbing
Local pressure
Species behavior therefore influences wear location.
Feeding often happens near the surface.
This can create high fish activity around upper side sections.
However, uneaten feed may sink toward the bottom.
This can increase:
Organic buildup
Fouling
Different parts of the cage are affected in different ways.
Where the side net meets the bottom net, stress directions change.
These corner zones may experience:
Pulling from the sides
Downward weight
Current movement
This combination can create concentrated stress.
Bottom corners should be inspected carefully for:
Fraying
Knot damage
Mesh distortion
Biofouling does not always grow evenly.
Light, water movement, and nutrients influence growth.
Side nets near the surface may receive:
More sunlight
Stronger water exchange
Bottom nets may experience:
Different organisms
More sediment
This can create different fouling patterns.
Barnacles and shell-forming organisms can create hard surfaces.
If these grow near bottom structures, they may rub against the net.
When the cage moves, hard fouling can cause:
Cutting
Scraping
This can accelerate damage.
Side nets may be easier to reach.
Bottom nets can be harder to inspect and clean because they are:
Deeper
Less visible
This can allow:
Fouling
Small damage
to remain unnoticed longer.
Maintenance plans should specifically include the bottom section.
Damage near the surface may be easier to detect.
Bottom-net problems may remain hidden.
Possible issues include:
Torn mesh
Broken twine
Loose attachments
Underwater cameras or diver inspections may be needed for deeper cages.
A side-net tear may create an escape opening.
A bottom-net failure can also create a large escape path.
Because fish may move downward or currents may enlarge the opening, bottom damage should be taken seriously.
Preventive inspection is critical.
Some cage designs use different net specifications in different sections.
For example, the bottom may require:
Stronger twine
Reinforced construction
The correct design depends on:
Fish species
Cage type
Current conditions
One uniform specification may not always be ideal.
Bottom sections exposed to abrasion may benefit from stronger construction.
Possible options include:
Thicker twine
Reinforced borders
However, stronger netting may also increase:
Weight
Drag
Design should balance durability and hydrodynamic performance.
Typical side-net problems may include:
Twine fatigue
Mesh stretching
Typical bottom-net problems may include more:
Abrasion
Local wear
Sediment damage
Understanding this difference helps identify the cause of failure.
If the net is installed unevenly, some bottom areas may carry too much tension.
Possible causes include:
Uneven weights
Poor attachment
Incorrect dimensions
This can create localized damage.
Balanced installation helps distribute load.
Strong currents can deform the entire cage.
If side nets bow inward, tension may transfer toward:
Bottom edges
Corners
The bottom can then experience additional stress.
This shows why cage sections cannot be evaluated completely independently.
Some cage systems include:
Feeding pipes
Sensors
Structural components
If equipment contacts the net, movement can create abrasion.
Any contact point should be monitored.
Predators may approach different parts of the cage.
Some may attack:
Side nets
Others may approach from below.
Predator contact can cause:
Biting
Scratching
Impact
In high-risk areas, predator netting may be needed.
A good inspection plan should treat side and bottom nets differently.
Focus on:
Current-facing areas
Frame contacts
Attachment points
Focus on:
Corners
Weight connections
Sediment contact
High-fouling areas
This makes inspection more effective.
Side-net repairs may be easier because damaged areas are more accessible.
Bottom repairs can be more difficult.
The cage may need:
Diving work
Partial lifting
This increases maintenance cost.
Preventive care is especially valuable for bottom nets.
Several practices can help.
Prevent unnecessary contact with the seabed.
Check that loads are evenly distributed.
Reduce weight and abrasion.
Avoid sharp surfaces.
Choose strength according to wear risk.
For side nets:
Maintain correct tension
Reduce sharp frame contact
Clean fouling regularly
Inspect current-facing sections
Monitoring deformation is also important.
Fish cage bottom nets and side nets may be connected, but they experience different working conditions.
Side nets are often more affected by:
Currents
Repeated deformation
Horizontal loading
Bottom nets may experience more:
Weight concentration
Sediment
Abrasion
Difficult maintenance
The best aquaculture net system should therefore consider each section separately.
At PL Fishery, we manufacture PE fish cage nets, aquaculture nets, fishing nets, marine netting, fishing ropes, and customized solutions for different farming environments.
Need fish cage netting designed for different side, bottom, or reinforcement requirements? Contact us with your cage dimensions, fish species, current conditions, and mesh requirements, and our factory team can help recommend or customize a suitable solution.https://plfishery.com/