WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Why Fishing Net Edges Curl After Cutting

By plfishery August 11th, 2026 64 views
Catalog

Why Fishing Net Edges Curl After Cutting

A fishing net panel may look flat and stable before cutting, but once the edge is trimmed, the newly cut section can begin to:

  • Curl inward

  • Roll outward

  • Twist

  • Shrink

  • Become wavy

This is common in flexible synthetic netting.

The main reason is that cutting changes the local force balance.

Before cutting, each mesh is connected to neighboring rows and shares tension across the panel. Once one side is released, the edge can recover toward its preferred shape.

The key principle is:

A cut fishing net edge is no longer mechanically balanced in the same way as the interior mesh.


1. Cutting Releases Residual Tension

During production, netting may be held under tension while:

  • Knots are formed

  • Mesh is stretched

  • Heat setting is applied

  • The panel is wound or packed

Some of that tension can remain inside the finished structure.

When the edge is cut, the restrained twines are released.

They may contract or rotate, causing the edge to curl.


2. Interior Mesh Is Balanced by Neighboring Rows

A mesh inside the panel is connected on every side.

Forces are distributed through surrounding knots and twines.

At the edge, this balance disappears.

One side of the mesh no longer has an opposing row.

This asymmetry allows the edge to deform more easily.


3. Diamond Mesh Naturally Wants to Rotate

Diamond-shaped mesh is flexible.

When one side is released, the mesh angle can change.

The opening may become:

  • Narrower

  • Taller

  • Wider

  • More diagonal

A whole sequence of rotating edge meshes can create visible curling.


4. Knot Orientation Influences Curl Direction

Knotted netting is not perfectly symmetrical.

Each knot has:

  • A direction

  • A tightening pattern

  • A local bend

When a panel is cut, repeated knot orientation along the edge can make the entire border curl in a similar direction.

This is why some cut edges roll consistently inward or outward.


5. Twisted Twine Can Store Torque

Twisted twine contains internal rotational force.

While the twine is locked into the complete mesh, much of this torque is restrained.

After cutting, the exposed twine ends may try to untwist or rotate.

This can contribute to:

  • Curling

  • Edge twisting

  • Loose strand ends

The effect is often more obvious in heavily twisted constructions.


6. Heat Setting Can Lock In Uneven Stress

Heat setting is used to stabilize net geometry.

If the net is held under non-uniform tension during the process, different areas may retain different residual stresses after cooling.

When the panel is later cut, those stresses are released unevenly.

The result can be:

  • Curling

  • Local shrinkage

  • Wavy edges


7. Incomplete Heat Setting Can Increase Curling

If dimensional stabilization is insufficient, the net may continue to recover after cutting.

This can make the edge less stable than expected.

However, some curling can still occur even in properly heat-set netting because the boundary condition has changed.


8. Cutting Direction Matters

A panel cut along one mesh direction may behave differently from one cut diagonally or across another orientation.

Different cutting paths expose different:

  • Knot positions

  • Twine directions

  • Mesh angles

Therefore, curl behavior can depend on where the panel is trimmed.


9. Cutting Through Knots Can Create Irregular Edges

If the cut passes too close to knots, the edge may contain:

  • Unequal twine lengths

  • Partial knots

  • Loose tails

  • Different tension points

This creates a less stable border and can increase local curling.


10. Cutting Between Knots Can Also Release Mesh Geometry

Even when no knot is damaged, cutting the connecting twine changes how nearby mesh shares load.

The first few rows may rotate to reach a new equilibrium.

This can create a wavy edge rather than a perfectly straight one.


11. Uneven Twine Tension Makes Curling Worse

If the original panel already contains different tension zones, the cut edge may not recover uniformly.

Some sections may:

  • Curl strongly

  • Stay relatively straight

  • Pull inward

  • Twist sideways

A variable curl pattern can therefore indicate pre-existing tension differences.


12. Packaging Can Add Temporary Curl

Netting stored in a tight roll or folded package can develop temporary shape memory.

After cutting, the edge may follow the curve created during storage.

This type of curl may reduce after:

  • Unfolding

  • Relaxation

  • Light tensioning

Do not judge final dimensional stability immediately after unpacking.


13. Heat From Cutting Can Affect the Edge

Some synthetic nets are cut with heated tools.

This can help seal loose filaments, but excessive heat can also:

  • Shrink the local material

  • Harden the edge

  • Create uneven contraction

If one side receives more heat than another, the edge may curl toward the shorter or stiffer side.


14. Melted Ends Can Become Stiff

Heat-sealed twine ends may form small hardened tips.

A continuous line of stiffened ends can change how the edge bends.

The net may no longer drape naturally.

This is especially noticeable in soft, flexible panels.


15. Mechanical Cutting Can Leave Loose Ends

Cold cutting avoids thermal shrinkage but may leave:

  • Frayed strands

  • Loose twist

  • Unfinished knots

These can change edge appearance and make handling more difficult.

The best cutting method depends on net construction and the intended finishing process.


16. Edge Curl Can Increase After Washing or Wetting

Some netting changes geometry slightly when:

  • Wet

  • Dried

  • Re-tensioned

Water itself may not significantly penetrate PE internally, but wetting can change friction, knot seating, and overall handling.

A cut edge may therefore look different before and after marine exposure.


17. Borders Help Control Curling

A border rope or finished selvedge restrains the edge.

It can:

  • Stabilize mesh angle

  • Distribute tension

  • Reduce rolling

  • Improve handling

This is one reason custom panels often receive reinforced edges after cutting.


18. Lacing Tension Must Be Controlled

Adding a border does not automatically solve the problem.

If lacing is too tight, it can create:

  • Gathering

  • Puckering

  • New edge curl

  • Mesh distortion

The border must match the effective edge length.


19. An Over-Short Border Can Pull the Edge Inward

If the border rope is shorter than the intended net edge, the net may bunch or curl toward it.

This can look like a cutting defect even though the real problem is finishing geometry.

Always separate:

Cutting Behavior

from

Border-Length Mismatch


20. Curling Can Change Final Panel Dimensions

A curled edge may make the panel appear:

  • Narrower

  • Shorter

  • Uneven

If measurements are taken immediately after cutting, the result may be misleading.

Use a defined relaxation and measurement condition.


21. Severe Curling Can Complicate Installation

Strong edge curl can make it harder to:

  • Align borders

  • Install attachment loops

  • Join panels

  • Maintain mesh orientation

Operators may apply excessive tension to force the edge flat, creating new stress.


22. Edge Curl Can Increase Local Abrasion

A rolled or twisted edge may contact:

  • Frames

  • Pipes

  • Hardware

  • Adjacent netting

more frequently.

Repeated contact can create premature wear.


23. How to Check Whether Curling Is Temporary

After cutting:

  1. Lay or suspend the panel without excessive tension.

  2. Allow it to relax.

  3. Compare both sides.

  4. Apply light, uniform tension.

  5. Observe whether the curl reduces.

Temporary packaging or residual-set curl often improves.

Persistent strong curling deserves further investigation.


24. Compare Different Cut Locations

If possible, compare test cuts from different areas.

If every edge curls similarly, the behavior may be inherent to the construction.

If only one zone curls strongly, possible causes include:

  • Uneven heat setting

  • Tension variation

  • Local material differences


25. Compare Curl Direction

Consistent curl direction may point to:

  • Knot orientation

  • Twine torque

  • Production direction

Random curl may suggest:

  • Uneven cutting

  • Variable tension

  • Local finishing differences

The pattern itself can provide useful clues.


26. When Edge Curl Should Be Considered a Quality Concern

Further investigation is justified when curling:

  • Prevents correct panel dimensions

  • Produces severe mesh distortion

  • Causes border assembly problems

  • Varies strongly within one batch

  • Does not reduce after relaxation

  • Creates repeated contact or abrasion

The acceptance level should be linked to the intended application.


27. Do Not Judge Edge Quality From Flatness Alone

A perfectly flat cut edge is not automatically stronger.

Likewise, a mildly curled edge is not automatically defective.

More important questions are:

  • Does the panel meet dimensions?

  • Is mesh geometry stable?

  • Can the edge be finished correctly?

  • Does the curl create stress or installation problems?


28. Define Finishing Requirements Before Production

For custom fishing nets, buyers should specify:

  • Cutting method

  • Finished edge type

  • Border requirement

  • Heat sealing requirement

  • Dimensional tolerance

  • Relaxation condition

This reduces disputes after trimming and assembly.


Practical Edge-Curl Inspection Checklist

Check after cutting:

✔ Curl direction
✔ Curl severity
✔ Mesh distortion
✔ Knot condition
✔ Loose twine ends
✔ Heat damage
✔ Local shrinkage
✔ Edge waviness

Compare:

✔ Different panel areas
✔ Opposite edges
✔ Before and after relaxation
✔ Before and after light tension

Check finishing:

✔ Border-rope length
✔ Lacing tension
✔ Selvedge construction
✔ Attachment alignment

Investigate further when:

✔ Curling is severe
✔ Only one area behaves differently
✔ Panel dimensions change significantly
✔ Edge remains rigid after relaxation
✔ Curl creates hardware contact


Conclusion: Cutting Changes the Mechanical Balance of Fishing Net Mesh

Fishing net edges curl after cutting because the edge is suddenly released from the balanced structure of the full panel.

Common contributors include:

  • Residual tension

  • Diamond-mesh rotation

  • Knot orientation

  • Twine torque

  • Heat setting

  • Cutting heat

  • Packaging deformation

  • Border mismatch

The key principle is:

A Cut Edge Is a New Structural Boundary, So It Should Not Be Expected to Behave Exactly Like the Interior of the Net.

Reliable finishing combines:

Controlled Cutting + Relaxation + Mesh Inspection + Correct Border Length + Balanced Lacing + Dimensional Verification

At PL Fishery, we manufacture PE fishing nets, fish cage panels, aquaculture netting, reinforced borders, custom-cut panels, attachment loops, repair mesh, repair twine, marine ropes, chicken nets, and customized net products.

To purchase or customize fishing netting, send PL Fishery your material, mesh size and measurement method, twine construction, panel dimensions, cutting method, finished-edge requirement, border structure, and dimensional tolerances so our factory can prepare a clear production and finishing specification.https://plfishery.com/

Leave a message
Name
Email *
Message
Message Us