WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Why Fishing Nets Change Shape Underwater: Currents, Mesh and Net Deformation

By plfishery July 31st, 2026 101 views
Catalog

Why Fishing Nets Change Shape Underwater

A fishing net may look perfectly straight, evenly stretched, and carefully measured when it is laid across a factory floor. Once it enters the water, however, it becomes a completely different structure.

Currents push against the mesh. Waves pull the upper and lower edges in different directions. Floats lift the top line, sinkers draw the bottom downward, and fish create small but repeated impacts from inside the enclosure.

The net begins to curve, narrow, expand, vibrate, and sometimes twist.

These movements are not random. They are controlled by water pressure, mesh geometry, twine structure, installation tension, fouling, and the way loads travel through the entire netting system.

Understanding these changes helps fishermen, fish farmers, engineers, and buyers choose more suitable netting and avoid premature damage.

A Net Is Not a Solid Wall

A solid wall blocks water almost completely. A fishing net allows water to pass through thousands of openings.

This open structure reduces resistance, but it does not eliminate it.

Every strand interrupts the flow. Water separates around the twine, travels through the mesh, and rejoins on the opposite side. This process creates drag.

When current speed is low, the force may be small. As the current becomes faster, pressure increases rapidly.

The net responds by moving away from the current. Instead of remaining flat, it develops a curved or bag-like shape.

This is similar to the way a curtain moves when air enters through an open window. The material is flexible, so it changes position rather than resisting like a rigid panel.

The Role of Mesh Geometry

Mesh geometry strongly affects how a net changes shape.

Diamond mesh is common because it is flexible and efficient to manufacture. When tension is applied vertically, the mesh may become narrower and longer. When tension is applied horizontally, it may become wider and shorter.

This means that the same net can have different apparent dimensions depending on how it is stretched.

Square mesh behaves differently. When properly supported, it can maintain a more consistent opening. However, its stability depends on the direction of installation and the way the borders are attached.

The angle of each mesh also influences water passage.

A widely opened mesh creates a larger open area. A narrow, elongated mesh creates a smaller effective opening, even if the twine length between knots has not changed.

For fish farmers, this matters because distorted mesh may reduce water circulation or change the escape risk for smaller fish.

Why Net Depth Can Decrease

An aquaculture cage may be designed with a specific depth, but the working depth underwater can become smaller.

When current pushes the side panels inward, the bottom section may rise or move toward the downstream side. The cage loses part of its internal volume.

This effect is called net deformation.

A cage that appears large at the surface may offer much less swimming space during strong currents.

Reduced volume can increase fish density, change swimming behavior, and affect oxygen distribution. In severe conditions, fish may gather in compressed areas and experience greater stress.

The amount of deformation depends on several factors:

  • Current speed;

  • Mesh size;

  • Twine diameter;

  • Net depth;

  • Weight distribution;

  • Floatation;

  • Bottom-ring design;

  • Fouling level;

  • Installation tension.

Heavier bottom systems can help maintain shape, but they also add load to ropes, frames, and attachment points. Every design choice therefore involves a balance.

Smaller Mesh Creates More Resistance

Imagine two panels of the same size.

One panel has large mesh openings. The other has very small openings.

The fine-mesh panel contains more twine across the same area. Because more material is exposed to moving water, it produces greater drag.

This does not mean that small mesh is undesirable. Juvenile fish and small aquatic species require openings that prevent escape.

However, smaller mesh may require stronger supports, more frequent cleaning, or a lower-current location.

Selecting mesh size only according to fish body size is not enough. Water conditions must also be considered.

A suitable net must retain the fish while still allowing adequate flow through the enclosure.

Twine Diameter Changes the Hydrodynamic Load

Thicker twine usually improves resistance to abrasion and physical damage. It may also provide higher strength, depending on the material and construction.

At the same time, thicker twine creates a larger surface for the current to push against.

This increases hydrodynamic resistance.

For example, a heavy-duty net may offer excellent durability in a quiet pond, but it could create much larger structural loads in a fast-moving coastal site.

The strongest-looking net is not automatically the best choice.

The correct product must match the operating environment, support system, maintenance schedule, and expected service period.

Biofouling Changes Everything

A clean net and a fouled net can behave like two completely different products.

Biofouling begins when microorganisms attach to the twine surface. Algae, barnacles, shellfish, hydroids, and other organisms may gradually cover the net.

The growth makes each strand thicker and reduces the open space inside the mesh.

Water can no longer pass through as easily.

Drag increases, the net moves farther downstream, and attachment points experience greater tension. The additional biological material also adds weight.

A net that performed safely when clean may become heavily loaded after several weeks or months underwater.

This is why cleaning schedules should be based on actual fouling conditions rather than a fixed calendar alone.

Warm water, sunlight, nutrient levels, salinity, season, and local species all influence growth speed.

Why Nets Vibrate

Fishing nets do not always move slowly. Under certain conditions, individual twines can vibrate rapidly.

As water passes around a strand, alternating pressure zones may form on opposite sides. These repeated forces can cause the twine to oscillate.

This movement is related to vortex shedding.

The vibration may be too small to notice from the surface, but repeated motion can create long-term fatigue. Knots, seams, border ropes, and contact points may wear gradually.

Loose net sections can also flap in waves or changing currents. When the same section bends thousands of times, fibers may weaken even without a single major overload.

This explains why some nets fail after long use despite never experiencing an obvious accident.

Load Does Not Stay in One Place

When current pushes against a large net panel, the force travels through the mesh.

Each twine transfers part of the load to nearby knots. Those knots transfer it to other meshes. Eventually, much of the pressure reaches the borders, ropes, corners, frames, anchors, or cage attachments.

The center of the net may look undamaged while the edge begins to tear.

Corners often experience especially complicated loading because several tension directions meet in one area.

If sewing is uneven, attachment spacing is too wide, or the border rope is unsuitable, force becomes concentrated.

A small weak point can then carry more pressure than the surrounding structure.

Good design spreads load gradually. It avoids abrupt changes between soft netting and rigid hardware.

The Effect of Over-Tight Installation

Many people believe that a tighter net is always a stronger net.

In practice, excessive tension can create problems.

A net pulled completely rigid has less ability to absorb movement. When a wave, fish, branch, boat, or floating object strikes it, the impact is transferred quickly to the nearest knots and attachments.

A slightly flexible structure can move and distribute the force over a wider area.

However, excessive looseness is also harmful.

Loose netting may fold, rub against itself, contact frames, or create pockets where fish become trapped.

The best installation uses controlled tension: firm enough to maintain shape, but flexible enough to respond to normal movement.

Temperature Can Affect Dimensions

Synthetic netting materials react to temperature, manufacturing tension, and heat treatment.

A net measured immediately after production may not have reached its final relaxed shape. Packaging pressure can compress it further.

After the roll is opened and allowed to rest, the meshes may redistribute. When the net is placed in water, some materials may stretch, contract, or soften slightly.

Nylon can absorb moisture and may show more dimensional change than low-water-absorption materials such as polyethylene.

Heat setting can improve dimensional stability, but the final result depends on the polymer, twine construction, processing temperature, and production control.

For accurate measurement, the net should be examined under a defined tension and according to a consistent method.

Fish Movement Also Influences the Net

Water is not the only force acting on a fish-cage net.

Fish may touch, push, bite, scrape, or swim repeatedly near the same area. Feeding activity can cause the stock to gather in concentrated zones.

These repeated contacts are usually much smaller than current pressure, but they may contribute to local wear.

Fish density and behavior can also influence cage shape. A large group moving together creates internal water movement and temporary pressure changes.

This is especially important near feeding points, corners, lights, and areas where fish frequently gather.

Regular inspections should therefore focus not only on the whole panel but also on high-activity zones.

Why the Upstream Side Often Wears Faster

The upstream side faces incoming water first.

It receives direct current pressure and may collect floating debris. Leaves, plastic fragments, branches, seaweed, or fishing waste can strike or remain pressed against the mesh.

The downstream side may experience different movement, including folding, suction, or repeated contact with internal structures.

Both areas require inspection, but the upstream panel often faces more direct environmental loading.

Operators should examine it after strong currents, storms, floods, or unusual debris events.

How to Reduce Excessive Deformation

No flexible fishing net can remain completely motionless underwater. The goal is to keep movement within a safe range.

Several strategies can help:

  • Choose a mesh size suitable for both fish retention and water flow;

  • Use twine strength appropriate for the current conditions;

  • Install sufficient bottom weight or structural support;

  • Maintain balanced tension;

  • Clean fouling before openings become seriously blocked;

  • Protect borders and contact points from abrasion;

  • Inspect corners, seams, ropes, and attachments regularly;

  • Remove trapped debris quickly;

  • Repair damaged mesh before the opening expands;

  • Match the net design to the specific farming location.

A net system should be treated as a complete structure. Strong netting cannot compensate for weak ropes, poor sewing, damaged frames, or unsuitable anchors.

Choosing a Net for Real Working Conditions

Product selection should begin with the actual environment rather than appearance alone.

Before ordering, buyers should consider:

  • Fish species and body size;

  • Required mesh opening;

  • Water depth;

  • Current speed;

  • Wave exposure;

  • Expected fouling;

  • Cleaning method;

  • Net replacement schedule;

  • Contact with metal or other rough surfaces;

  • Required length, depth, color, twine diameter, and border design.

A sample can show material, knot quality, color, and general construction. However, a small sample cannot fully reproduce the way a large net panel behaves underwater.

Large-scale performance depends on total area, installation method, support spacing, and environmental load.

A Living Structure Beneath the Surface

A fishing net is often described as a passive tool, but underwater it behaves more like a living structure.

It bends with the current, breathes through its mesh openings, carries growing organisms, receives thousands of repeated movements, and transfers forces from one strand to another.

Its shape is constantly changing, even when the changes are difficult to see from above.

Understanding this behavior helps operators recognize that net quality is not determined by thickness alone.

Material, mesh geometry, twine construction, finishing, installation, cleaning, and maintenance must work together.

A properly selected and correctly installed fishing net does more than contain fish. It maintains water exchange, protects the farming system, reduces structural risk, and supports healthier aquatic production.

For fishing-net purchasing, customized mesh sizes, twine specifications, colors, dimensions, reinforced borders, or factory production support, visit our product collection or contact us directly for a solution designed around your real working environment.

For purchase or customization inquiries, click the link below to learn more details

Leave a message
Name
Email *
Message
Message Us