Repeat orders are common in fishing net purchasing.
A buyer may simply tell the supplier:
“Please make it the same as last order.”
This sounds convenient.
But from a quality-control perspective, it can be risky.
The previous order may have included many details that were never formally documented, such as:
Twine construction
Mesh measurement method
Border-rope structure
Weight tolerance
Color shade
Join policy
Packaging method
Sampling requirements
If these details are not written again, different people may interpret “same” differently.
The key principle is:
“Same as last order” is a reference, not a complete specification.
A repeat order may be handled by:
A different salesperson
A different production manager
A different operator
A different buyer
Each person may remember the previous product differently.
One may focus on mesh size.
Another may remember only the color and roll length.
This creates room for specification drift.
Some product characteristics are often agreed informally during sampling.
For example:
Slightly heavier border rope
Specific knot tightness
Special folding method
Extra attachment loops
If these details were never added to the purchase specification, they may disappear in the next order.
A repeat order may use the same general material name, such as PE, but the actual raw-material source or formulation can change.
Possible differences include:
Resin grade
Additive package
UV stabilization
Recycled-content level
“Same PE net” does not automatically mean identical material behavior.
A previous order may have been accepted at a certain practical diameter.
If the repeat order only says “same as last time,” the supplier may use the nominal internal product code instead of the exact measured range.
This can create small but important changes.
Twine diameter should still be written and checked.
Two twines can have similar outside diameter while differing in:
Strand count
Twist level
Compactness
Filament arrangement
The net may look similar but behave differently in:
Flexibility
Knotting
Abrasion
Stretch
Construction should therefore be specified separately.
A previous order may have used:
Knot-to-knot
Stretched mesh
Clear opening
If the repeat order says only “25 mm mesh,” the factory and buyer may use different definitions.
The numeric value may remain the same while the actual product changes.
Even when the nominal mesh size is correct, acceptable variation matters.
If the first order used a tight tolerance and the repeat order does not define one, the second batch may be more variable.
“Same mesh size” does not automatically mean “same mesh consistency.”
A buyer may remember the previous roll as “about 20 kg.”
But was that:
Net weight?
Finished-panel weight?
Packed gross weight?
If the basis is unclear, the repeat order can differ while still appearing close.
Finished fishing nets may contain:
One border rope
Two border ropes
Different rope diameters
Different lacing
A small change here can affect:
Weight
Stiffness
Installation
Load distribution
Border details should be repeated in the new order.
Even if the same border material is used, a different effective border length can create:
Wavy edges
Pulled corners
Reduced panel depth
Mesh distortion
The previous installed geometry should be documented rather than assumed.
A repeat order may contain:
Different joining twine
Different overlap
Different stitch spacing
These changes may not be obvious from the product title.
If seam design matters, it should be written again.
Loop construction may change in:
Length
Diameter
Spacing
Knot style
Even small differences can affect installation tension.
A repeat order should not rely on memory for these details.
Was the previous order required to be:
100 m continuous with no panel splice?
Were twine joins allowed?
If this is not repeated, the supplier may treat hidden joins differently in the new production.
Continuous-length rules should always be explicit.
Packaging is often treated as a minor detail.
But changes in:
Folding
Compression
Strap tension
Bag size
can affect:
Edge curl
Border deformation
Installation handling
If the previous packaging worked well, document it.
“Same green” may not be enough.
Color can vary because of:
Pigment batch
Resin batch
Production conditions
If color matching is commercially important, the acceptable shade should be agreed more clearly.
A previous order may have included a defined strength target.
If the repeat PO says only “same as last order,” the testing requirement may not automatically follow.
Write again:
What is tested
Test method
Minimum value
Sampling rule
A strength value from one method cannot be compared directly with another.
Likewise, diameter, mesh, and length measurements can change depending on inspection method.
Repeat orders should preserve not only the target value but also the method.
Factories may update:
SKU codes
Yarn codes
Machine settings
Product naming
The same internal name may not always represent exactly the same historical construction.
Buyer-controlled specifications are safer than relying entirely on supplier codes.
A repeat order may be produced on:
Another machine
Another line
Another shift
This can influence:
Knot appearance
Mesh consistency
Tension
Finishing
A good specification helps maintain consistency across equipment changes.
Instructions such as:
“Make the border tight like before.”
are subjective.
One operator may make it tighter than another.
Measurable specifications are more repeatable than descriptive memory.
Sometimes the approved sample is:
Lost
Damaged
Stretched
Faded
Used in testing
If “same as last order” depends on that sample, the reference may no longer be reliable.
Keep written data with the golden sample.
A buyer may have accepted a minor defect because delivery was urgent.
That does not mean the defect should become the new standard.
For example:
Slightly short roll
Different color
Extra join
A repeat order should return to the intended specification, not automatically copy every accepted deviation.
A buyer may say:
“This batch is acceptable.”
That does not necessarily mean:
“Use this exact deviation for all future orders.”
Exceptions should be recorded separately.
The buyer may mean:
Same performance and construction.
The supplier may understand:
Same product name and approximate dimensions.
Both sides can believe they followed the instruction.
This is why measurable details matter.
The first order usually receives close attention.
Later orders may gradually change because small differences are accepted each time.
For example:
Order 1 → Small Change → Order 2 → Another Small Change → Order 5 Looks Noticeably Different
This is specification drift.
For repeat custom products, maintain one controlled specification sheet.
It should include:
Material
Mesh size
Measurement method
Twine construction
Diameter
Dimensions
Borders
Seams
Loops
Weight
Join policy
Tolerances
Each repeat order can reference this document.
A specification can be labeled:
Rev. A
Rev. B
Rev. C
If a customer changes one feature, update the revision.
This prevents factories from accidentally using an old version.
The approved physical sample should have a matching:
Sample code
Specification number
Revision
Approval date
The sample and document should function as one quality reference.
Even when a master specification exists, the PO should repeat the most important details.
For example:
Product code
Mesh
Twine
Dimensions
Quantity
Current revision
This reduces production mistakes.
An old PO may contain:
Outdated tolerances
Old packaging
Previous shipping marks
Temporary concessions
Review repeat orders before release.
Any difference from the approved standard should be documented before production.
Examples:
New twine
Different border
Different color
New packaging
The buyer can then approve or reject the change knowingly.
A supplier should not silently substitute critical components.
Where required, the specification can state that changes in:
Material
Twine construction
Border design
Production method
require buyer approval.
If the first order was checked at:
Beginning
Middle
End
but the repeat order is checked at only one easy location, consistency becomes harder to verify.
Maintain similar inspection logic across orders.
During incoming or pre-shipment inspection, compare the new batch against:
Written specification
Golden sample
Previous test records
This provides stronger control than memory.
Before issuing a repeat PO, confirm:
✔ Material
✔ Mesh size
✔ Measurement method
✔ Twine diameter
✔ Twine construction
✔ Panel dimensions
✔ Border structure
✔ Seam design
✔ Attachment loops
✔ Continuous-length requirement
✔ Weight requirement
✔ Strength requirement
✔ Packaging
✔ Tolerances
Reference:
✔ Golden sample code
✔ Specification revision
✔ Previous approved test method
✔ Current PO number
Do not rely only on:
✘ “Same as last order”
✘ Old photos
✘ Supplier memory
✘ Product name
✘ Approximate weight
Repeat orders should be easier than first orders—but not less controlled.
The phrase “same as last order” can be useful as a reference, but it cannot replace a complete written standard.
Without clear documentation, repeat orders can drift in:
Material
Mesh
Twine
Borders
Seams
Weight
Packaging
Testing
The key principle is:
If a feature matters to performance, cost, installation, or acceptance, it should remain written in every controlled product specification.
Reliable repeat purchasing combines:
Master Specification + Golden Sample + Revision Control + Clear Purchase Order + Consistent Inspection
At PL Fishery, we manufacture PE fishing nets, fish cage panels, aquaculture netting, reinforced borders, attachment loops, custom seams, repair mesh, repair twine, marine ropes, chicken nets, and customized net products.
To purchase or repeat a customized fishing net order, send PL Fishery your approved product code or previous specification together with any updated mesh, twine, panel, border, seam, length, packaging, testing, and tolerance requirements so our factory can confirm the current production standard before manufacturing.https://plfishery.com/