WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Why the Same Fishing Net Has Different Mesh Openings at Different Depths

By plfishery August 10th, 2026 75 views
Catalog

Why the Same Fishing Net Has Different Mesh Openings at Different Depths

A fish cage net may be manufactured from one continuous panel with the same:

  • Mesh size

  • Twine construction

  • Knot type

  • Material

  • Production batch

Yet after installation, the mesh openings near the surface may look different from those in the middle or near the bottom.

Some openings may appear:

  • Wider

  • Narrower

  • Taller

  • Shorter

  • More diagonal

  • Less regular

This does not automatically mean the net was manufactured with different mesh sizes.

In many cases, the difference comes from how the flexible mesh is loaded underwater.

The key principle is:

The nominal mesh may be the same throughout the panel, while the effective opening changes because each depth experiences different tension, geometry, and environmental load.


1. Diamond Mesh Changes Shape Under Load

A diamond-shaped mesh does not have one fixed width and height.

When pulled vertically, it becomes taller and narrower.

When pulled horizontally, it becomes wider and shorter.

Therefore, two sections made from identical mesh can show different clear openings simply because they are tensioned in different directions.


2. The Upper Net Is Strongly Controlled by the Frame

The top section is usually close to:

  • Floating collars

  • Frames

  • Border ropes

  • Attachment loops

These structures restrict movement.

If the upper border is tightly attached, the nearby mesh may be pulled more horizontally.

This can make the openings appear wider and shorter than deeper sections.


3. Middle Sections Have More Freedom to Bow

The center of a side panel is usually farther from rigid support.

Under current, it can bow downstream more freely.

As the panel curves, mesh angles change.

The result may be a different opening shape from both the top and bottom sections.


4. Bottom Mesh Is Influenced by Sinker Load

The lower net is affected by:

  • Sinker ropes

  • Sinker tubes

  • Bottom weights

  • Bottom-panel tension

Vertical loading can make some lower mesh openings taller and narrower.

If sinker weight is uneven, mesh size may also vary from one lower section to another.


5. Uneven Sinker Distribution Creates Local Differences

A heavy sinker point pulls nearby mesh more strongly.

A section between widely spaced sinkers may remain looser or rise under current.

This creates alternating:

  • Tight mesh

  • Loose mesh

  • Different opening angles

The original mesh side length may still be the same.


6. Current Speed Can Vary With Depth

Water movement is not always uniform from surface to bottom.

Different depths may experience different:

  • Current speed

  • Direction

  • Turbulence

  • Wave influence

This changes how strongly each part of the panel is pushed.


7. Surface Waves Affect Upper Mesh More Strongly

The upper section experiences repeated movement from waves and floating-frame motion.

This can cause rapid cycles of:

  • Tightening

  • Relaxation

  • Mesh rotation

  • Knot movement

Lower sections may move more slowly.

Over time, the upper and lower mesh may no longer sit in exactly the same geometry.


8. Tidal Reversal Changes Mesh Angle Again

In coastal aquaculture, current direction may reverse.

A mesh opening stretched in one direction during one tide may rotate in the opposite direction later.

This repeated movement can create local differences in:

  • Knot seating

  • Twine tension

  • Mesh recovery


9. Fouling Is Often Different at Different Depths

Biofouling does not grow uniformly.

The surface, middle, and lower zones may have different levels of:

  • Algae

  • Slime

  • Mussels

  • Barnacles

  • Other organisms

A heavily fouled section has less effective open area and greater drag.

This changes how the surrounding mesh is loaded.


10. Effective Mesh Opening Can Be Reduced by Fouling

The manufactured mesh opening may remain unchanged, but fouling physically occupies part of the opening.

This means there are two different concepts:

Manufactured Mesh Size

and

Effective Water-Flow Opening

A 25 mm nominal opening, for example, may provide much less clear water passage after heavy fouling.


11. Lower Fouling Can Add Significant Weight

Deep and bottom sections may accumulate heavier shell growth or sediment.

Additional weight pulls the mesh downward.

This can make lower openings appear more vertically elongated.


12. Uneven Cleaning Can Increase Depth Differences

If the upper section is cleaned frequently but the lower section remains fouled, the two zones behave differently.

The cleaned section becomes:

  • Lighter

  • More flexible

  • More permeable

The fouled section remains:

  • Heavier

  • Stiffer

  • Higher in drag

The transition between them may develop visibly different mesh geometry.


13. Border Tension Changes With Depth

Vertical borders may not carry uniform tension from top to bottom.

Differences can result from:

  • Attachment spacing

  • Border elongation

  • Sinker weight

  • Knot settling

A tight lower border and loose middle section can create different mesh openings along the same panel.


14. Attachment Points Create Local High-Tension Zones

Mesh close to an attachment loop is usually more restrained.

Mesh halfway between two attachments can move more freely.

Therefore, even at the same depth, openings may vary depending on distance from the nearest support.

This is why sampling only one mesh is unreliable.


15. Corners Behave Differently From Panel Centers

Corners usually contain:

  • Reinforced borders

  • Attachment loops

  • Extra knots

  • More concentrated load

Mesh near a corner may be more stretched or skewed than mesh in the center.

When comparing different depths, the sampling position should also be consistent horizontally.


16. Repairs Can Create Local Mesh Differences

A repair patch may have different:

  • Twine diameter

  • Mesh tension

  • Knot tightness

  • Flexibility

A tight patch can make nearby openings smaller.

A loose patch can allow them to become larger or more irregular.


17. Knot Movement Can Change Individual Openings

Repeated tension can cause some knots to:

  • Settle

  • Rotate

  • Slip slightly

This may release twine into one opening while shortening another.

The result is local mesh-size variation even though no row has been added or removed.


18. Long-Term Twine Creep Can Contribute

Synthetic twine under sustained tension may gradually deform over time.

The amount depends on:

  • Material

  • Load

  • Temperature

  • Construction

  • Service duration

Creep may be greater in heavily loaded sections, so different depths can gradually develop different geometry.


19. UV Exposure Makes Upper Zones Different

Upper and waterline sections generally receive more sunlight than deep submerged mesh.

Long-term UV exposure can change:

  • Flexibility

  • Elongation

  • Surface condition

This means the same tension may produce different deformation in aged upper twine compared with less-exposed lower twine.


20. Mesh Measurement Method Must Be Consistent

Before concluding that different depths contain different mesh sizes, confirm the measurement method.

Possible methods include:

  • Knot-to-knot

  • Stretched mesh

  • Clear opening

Do not compare a relaxed underwater opening with a fully stretched factory measurement.

The measurement condition must be defined.


21. Measure Several Consecutive Meshes

One opening may be distorted by a knot or local load.

For better comparison:

  1. Select a defined zone.

  2. Measure several consecutive openings.

  3. Use the same tension.

  4. Record the average and range.

  5. Repeat at other depths.

This provides a more representative result.


22. Compare the Same Horizontal Position

For example, compare:

  • Upper center

  • Middle center

  • Lower center

rather than comparing an upper corner with the lower center.

This helps separate the effect of depth from the effect of structural position.


23. Inspect Under Similar Current Conditions

Mesh geometry changes with water movement.

Measurements made during strong current should not be directly compared with measurements taken during slack water unless the operating condition is part of the analysis.


24. Why Different Openings Matter

Uneven effective mesh size can influence:

  • Water exchange

  • Fish containment

  • Fish behavior

  • Drag

  • Local tension

  • Cleaning efficiency

It may also indicate underlying problems such as:

  • Uneven sinkers

  • Attachment imbalance

  • Fouling

  • Border distortion

  • Repair tension


25. How to Reduce Depth-Related Mesh Differences

Maintain balanced sinker loads

Avoid strong local vertical pull.

Use consistent attachment spacing

Reduce unsupported spans.

Control installation tension

Do not over-tighten upper borders.

Clean fouling uniformly

Avoid large clean–fouled differences.

Inspect knots

Detect local slippage or rotation.

Use compatible repairs

Avoid stiff or overly tight patch boundaries.

Measure by zone

Track changes at the same locations over time.


Practical Depth-Based Mesh Inspection Checklist

Compare:

✔ Upper panel
✔ Waterline
✔ Middle panel
✔ Lower panel
✔ Bottom area

Check:

✔ Mesh opening shape
✔ Knot-to-knot dimension
✔ Mesh orientation
✔ Twine tension
✔ Fouling level
✔ Attachment spacing
✔ Sinker distribution
✔ Border condition
✔ Repair locations
✔ Current direction

Warning signs:

✔ Very wide upper openings
✔ Tall narrow lower openings
✔ Sudden change between two depths
✔ Skewed mesh around attachments
✔ Mesh distortion beside repairs
✔ Large differences after partial cleaning


Conclusion: The Same Mesh Can Look Different Because the Net Is a Flexible Structure

The same fishing net can have different mesh openings at different depths because each part of the panel experiences a different combination of:

  • Current

  • Wave motion

  • Vertical load

  • Sinker tension

  • Fouling

  • Attachments

  • UV exposure

  • Repairs

The key principle is:

The manufactured mesh specification may remain the same, while the effective opening changes with local geometry and operating load.

Reliable evaluation combines:

Consistent Mesh Measurement + Depth-Based Sampling + Sinker and Attachment Inspection + Fouling Control + Observation Under Current

At PL Fishery, we manufacture PE fishing nets, fish cage panels, aquaculture netting, reinforced borders, attachment loops, bottom netting, repair mesh, repair twine, marine ropes, chicken nets, and customized net products.

To purchase or customize fishing netting, send PL Fishery your required mesh size and measurement method, twine construction, panel dimensions, cage depth, attachment spacing, sinker system, operating current, fouling conditions, and dimensional tolerances so our factory can prepare a measurable production and inspection specification.

Leave a message
Name
Email *
Message
Message Us