WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Why the Same Fishing Net Has Different Mesh Openings at Different Depths

By plfishery August 10th, 2026 61 views
Catalog

Why the Same Fishing Net Has Different Mesh Openings at Different Depths

A fishing net can be manufactured from one continuous panel with the same mesh specification from top to bottom, yet the openings may look noticeably different after installation.

Near the surface, the mesh may appear wider. In the middle, it may become more diagonal. Near the bottom, it may look longer and narrower.

This does not necessarily mean the supplier produced several different mesh sizes in the same net.

The more common explanation is that a fishing net is a flexible structure. Its opening shape changes according to local tension, water movement, support, and weight.

The key principle is:

The nominal mesh size may remain unchanged while the effective opening changes at different depths.


1. Mesh Size Is Not Only About Twine Length

A diamond mesh is formed by four flexible sides connected by knots or junctions.

The same mesh can become:

  • Wider and shorter

  • Narrower and taller

  • More diagonal

  • Nearly closed

depending on how it is tensioned.

Therefore, the visible opening is controlled by geometry as well as manufactured dimension.


2. The Surface Is Restricted by the Cage Frame

The upper part of a fish cage is usually attached close to a floating collar, frame, or top border rope.

These components limit movement.

If the top border is pulled strongly in the horizontal direction, the upper mesh may open wider across the cage while becoming shorter vertically.

This creates a different appearance from the free-hanging middle section.


3. Mid-Depth Mesh Can Bow More Freely

The middle of the net panel is usually farther from rigid support.

Under current, this area can bow downstream.

As the panel curves, the mesh rotates.

The openings may therefore become more diagonal even though the original knot-to-knot mesh dimension has not changed.


4. The Bottom Is Influenced by Ballast

Lower sections are affected by sinkers, sinker tubes, or bottom rings.

These components pull the net downward.

Greater vertical tension tends to produce taller, narrower diamond openings.

If the ballast is heavy, this effect may become much more visible near the lower edge.


5. Uneven Sinker Weight Creates Local Variation

Not every part of the bottom border receives the same load if:

  • Sinker weights differ

  • Spacing is inconsistent

  • Some lines are shorter

  • A sinker is missing

One section may be strongly stretched while the neighboring section remains loose.

This creates different mesh openings even at the same depth.


6. Current Is Not Always Uniform From Surface to Bottom

Water velocity and direction can vary with depth.

The upper layer may be influenced more by:

  • Wind

  • Waves

  • Surface currents

Deeper sections may experience a different current direction or lower velocity.

Because drag changes with water movement, mesh geometry also changes.


7. Stronger Flow Can Rotate the Mesh

As current increases, the net bows farther downstream.

The panel must redistribute its geometry to accommodate this movement.

Some meshes become narrower, while others become more open in the horizontal direction.

This means the same mesh can look different during:

  • Slack water

  • Moderate current

  • Strong current


8. Fouling Changes the Effective Opening

Biofouling can partially block the space between twines.

Algae, slime, mussels, and barnacles reduce the clear opening available for water passage.

The actual manufactured mesh may remain unchanged, but the effective opening becomes smaller.

This distinction is important for aquaculture.


9. Fouling Is Usually Uneven With Depth

Marine growth may differ between the surface and deeper water because of differences in:

  • Light

  • Temperature

  • Nutrients

  • Water movement

  • Cleaning frequency

As a result, one depth may have much less clear opening than another.


10. Fouling Also Changes Drag

A fouled net does not only have smaller openings.

It also resists water more strongly.

Higher drag increases panel deformation.

This means fouling can affect mesh opening in two ways:

Physical blockage + Increased tension


11. Partial Cleaning Creates Sharp Differences

If only the upper part of a cage is cleaned, the lower section may remain heavily fouled.

The clean section allows more water through.

The dirty section produces greater resistance.

The boundary between the two zones can develop very different mesh shapes.


12. Attachment Spacing Changes Local Geometry

A mesh close to an attachment point is restrained.

A mesh halfway between two widely spaced attachments can move more freely.

This means two openings at the same depth may still look different.

Depth should therefore never be the only comparison variable.


13. Border Ropes Influence Nearby Mesh

Top, bottom, and vertical borders are usually stiffer than the main panel.

Mesh located close to a border may be more constrained.

If a border rope is too short, too tight, or uneven, nearby openings can become distorted.

This effect can be mistaken for incorrect mesh size.


14. Corners Are Different From Panel Centers

Corners combine several forces.

They may connect:

  • Horizontal borders

  • Vertical borders

  • Attachment loops

  • Sinker lines

Mesh near these locations often becomes more stretched or skewed than the center.

When comparing depth, use similar horizontal positions.


15. Repairs Can Change Local Opening Size

A repair may contain new twine with different:

  • Diameter

  • Stiffness

  • Knot tightness

  • Elastic behavior

If the repair is too tight, it can pull surrounding mesh inward.

If too loose, it can create enlarged or irregular openings.


16. Knot Movement Can Create Irregular Openings

Repeated loading can cause some knots to settle or rotate.

A small amount of twine may shift between neighboring mesh sides.

One opening becomes larger while another becomes smaller.

This is why local variation can appear even in one continuous panel.


17. Long-Term Load Can Cause Creep

Synthetic twine can gradually deform under sustained load.

This behavior depends on:

  • Material

  • Temperature

  • Load level

  • Time

  • Twine construction

Heavily loaded lower or attachment zones may therefore change differently from lightly loaded areas.


18. Upper Zones May Age Differently

Mesh near the waterline receives more exposure to:

  • Sunlight

  • Waves

  • Wet-dry cycling

  • Cleaning

Long-term aging can change flexibility and recovery.

As a result, the upper mesh may respond differently to tension even when its original specification matched the deeper section.


19. Nominal Mesh and Effective Opening Should Be Separated

This is one of the most important purchasing and inspection concepts.

Nominal mesh size describes the manufactured dimension according to a defined measurement method.

Effective opening describes the usable clear space under actual operating conditions.

The second can change with:

  • Tension

  • Angle

  • Fouling

  • Load

  • Water movement

These two values should not be confused.


20. Measurement Method Must Be Defined

Before comparing different depths, confirm how mesh size is defined.

Possible methods include:

  • Knot-to-knot

  • Stretched mesh

  • Clear opening

A relaxed underwater opening cannot be compared directly with a stretched factory measurement.


21. Measure Several Meshes, Not One

A single opening can be affected by a local knot or attachment.

For more reliable inspection:

  1. Select a defined location.

  2. Measure several consecutive meshes.

  3. Use the same tension method.

  4. Record both average and range.

  5. Repeat at other depths.

This gives a more representative result.


22. Compare Equivalent Locations

A good comparison might use:

  • Upper center

  • Middle center

  • Lower center

Avoid comparing an upper corner with a lower center because the structural conditions are different.


23. Record Current and Fouling Conditions

Mesh measurements should include the operating condition.

Record:

  • Current strength

  • Current direction

  • Fouling level

  • Cleaning status

  • Sinker condition

Without this information, later comparisons may be misleading.


24. Why Different Openings Matter

Different effective openings can influence:

  • Water exchange

  • Drag

  • Cage deformation

  • Fish containment

  • Local stress

  • Cleaning demand

A sudden change may also reveal an installation or maintenance problem.


25. What Buyers Should Ask Suppliers to Define

For custom fishing nets, the specification should clearly state:

  • Mesh measurement method

  • Mesh tolerance

  • Twine construction

  • Panel dimensions

  • Hanging ratio

  • Border design

  • Attachment spacing

This reduces disputes when field openings look different from factory measurements.


Practical Depth-Based Mesh Inspection Checklist

Check the same net at:

✔ Surface zone
✔ Mid-depth
✔ Lower side wall
✔ Bottom area

Record:

✔ Mesh measurement method
✔ Mesh orientation
✔ Opening shape
✔ Attachment spacing
✔ Border tension
✔ Sinker load
✔ Current direction
✔ Fouling level
✔ Repair locations

Look for:

✔ Sudden opening changes
✔ Narrow elongated mesh
✔ Very wide upper mesh
✔ Irregular knots
✔ Distortion near borders
✔ Different geometry after cleaning


Conclusion: The Same Net Can Have Different Effective Openings

Fishing net mesh openings can vary with depth even when the panel was manufactured to one consistent specification.

The main causes include:

  • Different support conditions

  • Water-current variation

  • Sinker loading

  • Fouling

  • Attachment spacing

  • Border tension

  • Knot movement

  • Long-term deformation

The key principle is:

The manufactured mesh dimension belongs to the product specification, while the effective underwater opening belongs to the operating condition.

Reliable evaluation requires:

Defined Mesh Measurement + Equivalent Sampling Positions + Depth-Based Inspection + Fouling Records + Load and Current Checks

At PL Fishery, we manufacture PE fishing nets, fish cage panels, aquaculture netting, reinforced borders, attachment loops, bottom panels, repair mesh, repair twine, marine ropes, chicken nets, and customized net products.

To purchase or customize fishing netting, send PL Fishery your required mesh size and measurement method, twine construction, panel dimensions, cage depth, hanging ratio, attachment spacing, sinker system, operating current, and mesh tolerance so our factory can prepare a clear production and inspection specification.https://plfishery.com/

Leave a message
Name
Email *
Message
Message Us